国际标准: |
ISO 2178:1982 | 在磁性基体上的非磁性复盖层--复盖层厚度测量--磁测法 |
Non-magnetic coatings on magnetic substrates -- Measurement of coating thickness-Magnetic method |
ISO 2360:2003 | 在非磁性金属基体上的非导电复盖层--复盖层厚度测量--涡流法 |
Non-conductive coatings on non-magnetic electrically conductive basis materials-Measurement of coating thickness- Amplitude-sensitive eddy current method |
ISO 2361-82E | 磁性和非磁性基体上镀镍层厚度的磁性测量方法(NDT,87-2) |
ISO 2361:1982 | 在磁性和非磁性基体上的电镀层--镀层厚度测量--磁测法 |
Electrodeposited nickel coatings on magnetic and non-magnetic substrates-Measurement of coating thickness -- Magnetic method |
ISO N 237 | 铸钢件的磁粉探伤 |
ISO 3059:2002 | 无损检测 渗透检验和磁粉检验 观察条件 黑光源的间接评定方法(TC135) |
ISO 4309-1981 | 起重机械用钢丝绳检验和报废实用规范 |
ISO5065/ 1 | 磁粉检验指示器-第1部分:特性 |
ISO5065/ 2 | 磁粉检验指示器-第2部分:试验 |
ISO DP 5578 | 磁粉检验用磁化设备 |
ISO 4986:1992 | 钢铸件-磁粉检验 |
Steel castings-Magnetic particle inspection |
ISO 6933:1986 | 铁道轧材--磁粉验收试验 |
Railway rolling stock material -- Magnetic particle acceptance testing |
ISO 9302:1994 | 无缝和焊接( 埋弧焊除外) 承压钢管--验证液压密封性的电磁检验 |
Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes-Electromagnetic testing for verification of hydraulic leak-tightness |
ISO 9304:1989 | 无缝和焊接( 埋弧焊除外) 承压钢管--探测缺陷的涡流检验 |
Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes-Eddy current testing for the detection of imperfections |
ISO 9402:1989 | 无缝和焊接( 埋弧焊除外) 承压钢管--探测铁磁性钢管纵向缺陷的全圆周磁传感器/ 漏磁检验 |
Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes-Full peripheral magnetic transducer/flux leakage testing of ferromagnetic steel tubes for the detection of longitudinal imperfections |
ISO 9598:1989 | 受压无缝钢管 探测铁磁性钢管横向缺陷的全圆周磁传感器/ 漏磁检验 |
Seamless steel tubes for pressure purposes-Full peripheral magnetic transducer/flux leakage testing of ferromagnetic steel tubes for the detection of transverse imperfections |
ISO 9934-1:2001 | 无损检测--磁粉检测--第1部分:总则 (GB/T 15822.1-2005 IDT) |
Non-destructive testing-Magnetic particle testing-Part 1: General principles |
ISO 9934-2:2002 | 无损检测--磁粉检测--第2部分:检测介质 (GB/T 15822.2-2005 IDT) |
Non-destructive testing-Magnetic particle testing-Part 2: Detection media |
ISO 9934-3:2002 | 无损检测--磁粉检测--第3部分:设备 (GB/T 15822.3-2005 IDT) |
Non-destructive testing-Magnetic particle testing-Part 3: Equipment |
ISO 12718:2008 | 无损检测--涡流检测--词汇 |
Non-destructive testing -- Eddy current testing --Vocabulary |
ISO 13664:1997 | 无缝和焊制承压钢管 管端分层缺陷的磁粉检测 |
Seamless and welded steel tubes for pressure purposes-Magnetic particle inspection of the tube ends for the detection of laminar imperfections |
ISO 13665:1997 | 无缝和焊制承压钢管 管体表面缺陷的磁粉检测 |
Seamless and welded steel tubes for pressure purposes-Magnetic particle inspection of the tube body for the detection of surface imperfections |
ISO 15548-1:2008 | 无损检测--涡流检验设备--第1部分:仪器特性与 验证 |
Non-destructive testing -- Equipment for eddy current examination -- Part 1: Instrument characteristics and verification |
ISO 15548-2:2008 | 无损检测--涡流检验设备--第2部分:探头特性与 验证 |
Non-destructive testing -- Equipment for eddy current examination -- Part 2: Probe characteristics and verification |
ISO 15548-3:2008 | 无损检测--涡流检验设备--第3部分:系统特性与 验证(GB/T 14480.3-2008 IDT) |
Non-destructive testing -- Equipment for eddy current examination -- Part 3: System characteristics and verification |
ISO 15549:2008 | 无损检测--涡流检验--总则 |
Non-destructive testing -- Eddy current testing --General principles |
ISO 17638:2003 | 焊缝无损检测--磁粉检测 |
Non-destructive testing of welds-Magnetic particle testing |
ISO 17643:2005 | 焊缝无损检测--利用复平面分析的涡流检测 |
Non-destructive testing of welds-Eddy current testing of welds by complex-plane analysis |
ISO 23278:2006 | 焊缝无损检测--焊缝的磁粉检测--验收等级 |
ISO 24497-1 | 无损检测--金属磁存储器-第1部分:一般要求 |
ISO 24497-2 | 无损检测--金属磁存储器-第2部分:术语与定义 |
ISO 24497-3 | 无损检测--金属磁存储器-第3部分:焊缝的检验 |
ISO 25902-1 | 钛管无损检测--第1部分:涡流检验 |
欧洲标准化委员会标准: |
EN 1290:1998 | 焊缝无损检测 焊缝的磁粉检验 |
Non-destructive examination of welds-Magnetic particle examination of welds |
EN 1291:1998 | 焊缝无损检测 焊缝的磁粉检验 验收等级 |
Non-destructive examination of welds-Magnetic particle testing of welds-Acceptance levels |
EN 1330-5:1998 | 无损检测 术语 第5部分:涡流检测所用术语 |
Non-destructive testing-Terminology-Part 5:Terms used in Eddy current testing |
EN 1330-7:2005 | 无损检测 术语 第7部分:磁粉检测所用术语 |
Non-destructive testing - Terminology - Part 7: Terms used in magnetic particle testing |
EN 1369:1996 | 铸件磁粉检查 |
EN 1711:2000 | 焊缝无损检测 基于复平面分析的焊缝涡流检测 |
Non-destructive examination of welds-Eddy current examination of welds by complex plane analysis |
EN 1956: | 无损检测 渗透检测和磁粉检测 |
EN 1971: | 铜和铜合金的涡流检测 |
EN 2857/1: | 磁粉检测 总则 |
EN 2857/2: | 检查要求 |
EN ISO 3059:2001 | 无损检测 渗透检测和磁粉检测 观察条件 |
Non-destructive testing-Penetrant testing and magnetic particle testing-Viewing conditions(ISO 3059:2001) |
EN ISO 9934-1:2001/A1:2003 | 无损检测 磁粉检测 第1部分:总则 |
Non-destructive testing-Magnetic particle testing-Part 1:General principles(ISO 9934-1:2003) |
EN ISO 9934-2:2002 | 无损检测 磁粉检测 第2部分:探测介质 |
Non-destructive testing-Magnetic particle testing-Part 2etection media(ISO 9934-2:2002) |
EN ISO 9934-3:2002 | 无损检测 磁粉检测 第3部分:设备 |
Non-destructive testing-Magnetic particle testing-Part 3:Equipment(ISO 9934-3:2002) |
EN 10228/1:1999 | 磁粉检查 |
EN 10246/1:1996 | 无缝与焊接(埋弧焊除外)铁磁性钢管的自动电磁检测-验证液压密封性 |
EN 10246/2:2000 | 无缝与焊接(埋弧焊除外)奥氏体和奥氏体铁素体钢管的自动涡流检测-验证液压密封性 |
EN 10246/3:1999 | 无缝与焊接(埋弧焊除外)钢管的自动涡流检测-探伤 |
EN 10246/4:1999 | 无缝铁磁性钢管的自动全圆周磁传感器/漏磁检测-检测横向缺陷 |
EN 10246/5:1999 | 无缝与焊接(埋弧焊除外)铁磁性钢管的自动全圆周磁传感器/漏磁检测-检测纵向缺陷 |
EN 10246/12:2000 | 无缝与焊接铁磁性钢管的磁粉检测-检测表面缺陷 |
EN 10246/18:2000 | 无缝与焊接铁磁性钢管管端面的磁粉检测-检测层状缺陷 |
EN 12084:2001/A1:2003 | 无损检测 涡流检测 一般原理和指南 |
Non-destructive testing-Eddy current testing-General principles and guidelines |
EN ISO 12718:2008 | 无损检测 涡流检测 词汇 |
Non-destructive testing - Eddy current testing - Vocabulary (ISO 12718:2008) |
EN 13860-1:2003 | 无损检测 涡流检测 设备性能与验证 第1部分:仪器性能与验证 |
Non-destructive testing-Eddy current examination-Equipment characteristics and verification-Part 1:Instrument characteristics and verification |
EN 13860-2:2003 | 无损检测 涡流检测 设备性能与验证 第2部分:探头性能与验证 |
Non-destructive testing-Eddy current examination-Equipment characteristics and verification-Part 2robe characteristics and verification |
EN 13860-3:2003 | 无损检测 涡流检测 设备性能与验证 第3部分:系统性能与验证 |
Non-destructive testing-Eddy current examination-Equipment characteristics and verification-Part 3:System characteristics and verification |
EN ISO 15548-1:2008 | 无损检测 涡流检验设备 第1部分:仪器特性与验证 |
Non-destructive testing - Equipment for eddy current examination - Part 1:Instrument characteristics and verification (ISO 15548-1:2008) |
EN ISO 15548-1:2008/AC:2010 | 无损检测 涡流检验设备 第1部分:仪器特性与验证 技术勘误表 |
Non-destructive testing - Equipment for eddy current examination - Part 1:Instrument characteristics and verification - Technical Corrigendum 1 (ISO 15548-1:2008/Cor 1:2010) |
EN ISO 15548-2:2008 | 无损检测 涡流检验设备 第2部分:探头特性与验证 |
Non-destructive testing - Equipment for eddy current examination - Part 2robe characteristics and verification (ISO 15548-2:2008) |
EN ISO 15548-3:2008 | 无损检测 涡流检验设备 第3部分:系统特性与验证 |
Non-destructive testing - Equipment for eddy current examination - Part 3:System characteristics and verification (ISO 15548-3:2008) |
EN ISO 15549:2010 | 无损检测 涡流检测 总则 |
Non-destructive testing - Eddy current testing - General principles (ISO 15549:2008) |
EN WI 45:2002 | 涡流检测设备 |
美国相关标准 |
AMS 2300G-91(R-95) | 优质航空用钢纯洁度的磁粉检验方法 |
MAM-2300A-92(R-99) | 优质航空用钢纯洁度的磁粉检验方法(米制) |
AMS 2301H-96 | 航空用钢纯洁度的磁粉检验方法 Cleanliness, Aircraft Quality Steel Magnetic Particle Inspection Procedure H |
MAM 2301-96 | 航空用钢纯洁度的磁粉检验方法(米制) |
AMS 2303D | 航空用马氏体耐蚀钢纯洁度的磁粉检验方法 |
MAM 2303A-93(R-98) | 航空用马氏体耐蚀钢纯洁度的磁粉检验方法(米制) |
AMS 2304-91(R-95) | 特种航空用钢纯洁度的磁粉检验方法 |
MAM 2304-91(R-95) | 特种航空用钢纯洁度的磁粉检验方法(米制) |
AMS-2308-94 | 磁橡胶检查 |
AMS-2309-94 | 磁橡胶检查材料 |
AMS 2442-93 | AMS 2442-93 零件的磁粉检验验收标准 Magnetic Particle Acceptance Criteria for Parts |
AMS 2640J-83(R-92) | AMS 2640J-83(R-92) 磁粉检验 已被ASTM E1444取代 1996年4月 |
AMS 2641A-96 | AMS 2641A-96 磁粉检验用石油基载液 Vehicle, Magnetic Particle Inspection, Petroleum Base A |
AMS-2658A-91 | AMS-2658A-91 经热处理的铝合金零件硬度和电导率检查 |
AMS 3040B-95 | AMS 3040B-95 非荧光磁粉--干法 Magnetic Particles, Nonfluorescent, Dry Method B |
AMS 3041C-96 | AMS 3041C-96 非荧光磁粉--湿法,油磁悬液 Magnetic Particles, Nonfluorescent, Wet Method,Oil Vehicle, Ready- to- Use C |
AMS 3042C-96 | AMS 3042C-96 非荧光磁粉--湿法,水磁悬液 |
AMS 3043B-96 | AMS 3043B-96 非荧光磁粉--湿法,喷罐型油磁悬液 Magnetic Particles, Nonfluorescent, Wet Method,Oil Vehicle, Aerosol Packaged B |
AMS 3044D-96 | AMS 3044D-96 荧光磁粉--湿法,水磁悬液 |
AMS 3045C-96 | AMS 3045C-96 荧光磁粉--湿法,油磁悬液 Magnetic Particles, Fluorescent, Wet Method, Oil Vehicle Ready- to- Use C |
AMS 3046D-98 | AMS 3046D-98 荧光磁粉--湿法,喷罐型油磁悬液 Magnetic Particles, Fluorescent Wet Method, Oil Vehicle, Aerosol Packaged D |
ARP 891A | ARP 891A 通过测量电导率确定铝合金回火度(涡流法) |
ARP 4402-92(R-96) | ARP 4402-92(R-96) 飞机铝构件开口紧固孔的涡流检验 |
AS-4787-92(R-96) | AS-4787-92(R-96) 在航空发动机有色金属构件中圆孔的涡流检查(K) |
AS 4792-93 | AS 4792-93 用于水磁悬液磁粉检验的水调节剂 Water Conditioning Agents for Aqueous Magnetic Particle Inspection |
AS 5282 | AS 5282 用于磁粉检验的工具钢环形试样 Tool Steel Ring for Magnetic Particle Inspection |
AS 7114 | AS 7114 美国宇航局与国防部订约授权程序(NADCAP)要求-无损检测 |
AS 7114/ 2 | AS 7114/ 2 美国宇航局与国防部订约授权程序(NADCAP)要求-磁粉无损检测的审定 |
MAM 2300A | MAM 2300A 优质航空用钢纯洁度的磁粉检验方法(公制) |
MAM 2301 | MAM 2301 航空用钢纯洁度的磁粉检验方法(公制) |
MAM 2303B | MAM 2303B 航空用马氏体耐蚀钢纯洁度的磁粉检验方法(公制) |
MAM 2304 | MAM 2304 特种航空用钢纯洁度的磁粉检验方法(公制) |
ASTM A275/A275M-1998 | 钢锻件磁粉检验方法(A-1) Test Method for Magnetic Particle Examination of Steel Forgings |
ASTM A340-2001 | 与磁化试验有关的符号和定义的术语 |
Terminology of Symbols and Definitions Relating to Magnetic Testing |
ASTM A341/A341M-1995 | 用直流磁导计和弹道学法测定材料直流磁性能的试验方法 |
Test Method for Direct Current Magnetic Properties of Materials Using D-C Permeameters and the Ballistic Test Methods |
ASTM A342-1995 | 弱磁材料导磁率的试验方法 Test Methods for Permeability of Feebly Magnetic Materials |
ASTM A450-76 | 钢管涡流检测 |
ASTM A456/A 456M-1999 | 大型曲轴锻件磁粉检验的标准规范 |
Standard Specification for Magnetic Particle Examination of Large Crankshaft Forgings |
ASTM A556-65 | 无缝碳素钢管涡流检测 |
ASTM A596/A596M-1995 | 用弹道学法和环形试样测定材料直流磁性能的试验方法 |
Test Method for Direct-Current Magnetic Properties of Materials Using the Ballistic Method and Ring Specimens |
ASTM A772/A772M-1995 | 利用正弦电流测定材料交流磁导率的试验方法 |
Test Method for A-C Magnetic Permeability of Materials Using Sine Current |
ASTM A894/A894M-1995 | 磁性材料饱和磁化的试验方法 Test Method for Saturation Magnetization of Magnetic Materials |
ASTM A 903/A 903M-1999 | 钢铸件 磁粉和液体渗透检验的表面验收标准 |
Steel Castings, Surface Acceptance Standards, Magnetic Particle and Liquid Penetrant Inspection |
ASTM A966-1996 | 用交流电流检验钢锻件磁粉检验方法 |
Test Method for Magnetic Particle Examination of Steel Forgings Using Alternating Current |
ASTM A977-1997 | 使用磁滞曲线绘制仪测试高矫顽磁性永磁材料磁性能的标准试验方法 |
Standard Test Method for Magnetic Properties of High-Coercivity Permanent Magnet Materials Using Hysteresigraphs |
ASTM B193-1995 | 导电材料电阻率的测试方法 Test Method for Resistivity of Electrical Conductor Materials |
ASTM B244-1997 | 用涡流仪测量铝阳极化层及其它非磁性金属基体上绝缘涂层的厚度 |
Measurement of Thickness of Anodic Coatings on Aluminum and of Other Nonconductive Coatings on Nonmagnetic Basis Metals with Eddy-Current Instruments |
ASTM B342-70 | 材料导电率的涡流测量方法 |
ASTM B499-1996 | 磁性金属基体上非磁性涂层厚度测量的试验方法:磁性法(B-8) |
Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals |
ASTM B529-70 | 非磁性金属上非导电层厚度的涡流测量方法 |
ASTM B530-1996 | 用磁性法测量磁性和非磁性基体上的电镀镍层厚度的试验方法 |
Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Electrodeposited Nickel Coatings on Magnetic and Nonmagnetic Substrates |
ASTM B554-71 | 非金属上金属涂层厚度测量的推荐方法 |
ASTM C1238-1997 | 地下通道金属探测器的安装 Installation of Walk-Through Metal Detectors |
ASTM C1269-1997 | 内穿过式金属探测器操作灵敏度设置调整的标准规程 |
Standard Practice for Adjusting the Operational Sensitivity Setting of In-Plant Walk-Through Metal Detectors |
ASTM C1309-1997 | 内穿过式金属检测器性能评定的标准规程 |
Standard Practice for Performance Evaluation of In-Plant Walk-Through Metal Detectors |
ASTM D1186-93 | 铁基体上非磁性薄膜的干膜厚度无损测量方法 |
ASTM D1400-94 | 非铁金属基体上非导电覆盖层干膜厚度无损测量方法 |
ASTM D4166-1999 | 数字磁强仪测量非磁性材料厚度的试验方法 |
Test Method for Measurement of Thickness of Nonmagnetic Materials by Means of a Digital Magnetic Intensity Instrument |
ASTM D6639-2001 | 地下勘察用频域电磁法的标准指南 |
Standard Guide for Using the Frequency Domain Electromagnetic Method for Subsurface Investigations |
ASTM E45 | 确定钢中夹杂物含量的标准方法 |
ASTM E109-76 | 干粉法磁粉检验 |
ASTM E125-63(2008) | 铸铁件磁粉检验标准参考照片 Standard Reference Photographs for Magnetic Particle Indications on Ferrous Castings |
ASTM E138-76 | 湿法磁粉检验 |
ASTM E215-2011 | 铝合金无缝管电磁检测的标准化设备 |
Standard Practice for Standardizing Equipment for Electromagnetic Testing of Seamless Aluminum-Alloy Tube |
ASTM E243-2009 | 铜及铜合金管电磁(涡流) 检验标准方法 |
Standard Practice for Electromagnetic (Eddy-Current) Examination of Copper and Copper-Alloy Tubes |
ASTM E268-84a | 电磁检测术语定义 |
ASTM E269-84a | 磁粉检验术语定义 |
ASTM E309-2011 | 钢管制品磁饱和法涡流检验标准方法 |
Standard Practice for Eddy-Current Examination of Steel Tubular Products Using Magnetic Saturation |
ASTM E376-2011 | 用磁场或涡流(电磁的)检测方法测量涂层厚度的标准规范 |
Standard Practice for Measuring Coating Thickness by Magnetic-Field or Eddy-Current (Electromagnetic) Test Methods |
ASTM E426-98(2007) | 奥氏体不锈钢及类似合金无缝和焊接管制品电磁(涡流) 检验的标准方法 |
Standard Practice for Electromagnetic (Eddy-Current) Examination of Seamless and Welded Tubular Products, Austenitic Stainless Steel and Similar Alloys |
ASTM E566-2009 | 黑色金属电磁(涡流)分选的标准方法 |
Standard Practice for Electromagnetic (Eddy-Current) Sorting of Ferrous Metals |
ASTM E570-2009 | 铁磁性钢管制品漏磁检验的规程 |
Practice for Flux Leakage Examination of Ferromagnetic Steel Tubular Products |
ASTM E571-98(2007)e1 | 镍和镍合金管制品电磁(涡流) 检验的标准方法 |
Standard Practice for Electromagnetic (Eddy-Current) Examination of Nickel and Nickel Alloy Tubular Products |
ASTM E690-2010 | 非磁性热交换器管现场电磁(涡流)检验的标准方法 |
Standard Practice for In Situ Electromagnetic (Eddy-Current) Examination of Nonmagnetic Heat Exchanger Tubes |
ASTM E703-2009 | 有色金属电磁(涡流)分选的标准方法 |
Standard Practice for Electromagnetic (Eddy-Current) Sorting of Nonferrous Metals |
ASTM E709-2008 | 磁粉检测指南 Standard Guide for Magnetic Particle Testing |
ASTM E977-2005(2010) | 导电材料热电分选的标准方法 |
Standard Practice for Thermoelectric Sorting of Electrically conductive Materials |
ASTM E1004-2009 | 用电磁(涡流)法测定电导率的标准试验方法 |
Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method |
ASTM E1033-2009 | 电磁(涡流)法检验居里点温度以上F型连续焊(CW) 铁磁性管材的标准试验方法 |
Standard Practice for Electromagnetic(Eddy-Current) Examination of Type F-Continuously Welded(CW) Ferromagnetic Pipe and Tubing Above the Curie Temperature |
ASTM E1312-2009 | 电磁(涡流)法检验居里点温度以上铁磁性圆棒产品的标准试验方法 |
Standard Practice for Electromagnetic(Eddy-Current) Examination of Ferromagnetic Cylindrical Bar product Above the Curie Temperature |
ASTM E1444/E1444M-2011 | 磁粉检测标准试验方法 |
Standard Practice for Magnetic Particle Testing |
ASTM E1571-2011 | 铁磁性钢丝绳电磁检验的标准试验方法 |
Standard Practice for Electromagnetic Examination of Ferromagnetic Steel Wire Rope |
ASTM E1606-2009 | 电工用铜质再拉棒电磁(涡流) 检验的标准试验方法 |
Standard Practice for Electromagnetic(Eddy-Current) Examination of Copper Redraw Rod for Electrical Purposes |
ASTM E1629-2007 | 测定绝对式涡流探头阻抗的标准试验方法 |
Standard Practice for Determining the Impedance of Absolute Eddy Current Probes |
ASTM E2096/E2096M-2010 | 现场使用远场涡流检测铁磁性热交换器管 的标准试验方法 |
Standard Practice for In Situ Examination of Ferromagnetic Heat-Exchanger Tubes Using Remote Field Testing |
ASTM E2261-2007 | 使用交流电场测量技术检验焊缝的标准试验方法 |
Standard Practice for Examination of Welds Using the Alternating Current Field Measurement Technique |
ASTM E2297-2004 | 液体渗透和磁粉方法用UV-A与可见光源及强度计的指南 |
Guide for use of UV-A and Visible Light Sources and Meters used in the Liquid Penetrant and Magnetic Particle Methods |
ASTM E2337/E2337M-2010 | 互感电桥应用于锅炉管壁测厚的标准指南 |
Standard Guide for Mutual Inductance Bridge Applications for Wall Thickness Determinations in Boiler Tubing |
ASTM E2338-2011 | 用不带标准参考覆盖层的适当涡流传感器表征覆盖层特性的 标准试验方法 |
Standard Practice for Characterization of Coatings Using Conformable Eddy-Current Sensor without Coating Reference Standards |
ASTM F673-1990(1996) | 用非接触涡流仪测量半导体膜片电阻率的试验方法(F-1) |
Test Methods for Measuring Resistivity of Semiconductor Slices or Sheet Resistance of Semiconductor Films with a Noncontact Eddy-Current Gage |
ASTM G96-90(1996) | 固定设备在线腐蚀监测指南(电学和电磁学方法) |
MIL-M-6867C-69 | 磁性检验设备 |
MIL-I-6868E-76 | 磁粉检验方法(INDT,85-4) |
MIL-HDBK-728/4(92) | 磁粉检验 |
MIL-HDBK-728/2(92) | 涡流检验 |
MIL-STD-288(57) | 测定变形奥氏体钢磁导率的程序 |
MIL-STD-1537B(88) | 用涡流电导率测试法检验铝合金热处理质量 |
MIL-STD-2032(90) | 美国海军舰船用热交换器管涡流检验 |
MIL-M-6867C(69) | 磁粉检验设备 |
MIL-I-83387A(87) | 磁橡胶检查方法 |
MIL-P-85585(82) | 无屏蔽单线圈绝对测量的涡流探头 |
BAC 5424 | (美国波音公司)磁粉检验 |
BAC 5963 | 涡流检验 |
DPS 4.704 | (美国麦道公司)磁粉检验 |
DPS 4.704-1 | 磁粉检验--返修 |
DPS 4.704-2 | 磁粉检验--适用性 |
DPS 1.05 | 涡流法测电导率--设备与方法 |
API RP 2X-2004 | 海上结构建造的超声和磁粉检验推荐作法和技师考核指南 |